01-15-2019, 05:46 PM
1
Hello Folks,
I have started this discussion for CCIE R&S v5 H1.0 LAB Solution Verification. We will verify H1.0 Lab solution one by one so we can pass CCIE R&S LAB.
Lets start now with LAYER 2 TECHNOLOGY
1.1 SWITCH ADMINISTRATION
Configure the ACME headquarters network (AS 12345) as per the following requirements
before being refresh,
Configure the network of the new York office (AS 34567) as per the following requirements
I did the below configuration for Q 1.1 SWITCH ADMINISTRATION what did you think about this config
SW1:
SW1(config)#
SW1(config)#VTP domain CCIE
SW1(config)#VTP mode server
SW1(config)#VTP version 2
SW1(config)#VTP password CCIErock?
TO GET THE QUESTION MARK ENTERD, TYPE CTRL + V, AND THE ENTER THE ? CHARACTER
SW1(config)#Mac-address again 7200
SW2:
SW2(config)#VTP domain CCIE
SW2(config)#VTP mode client
SW2(config)#VTP password CCIErock?
TO GET THE QUESTION MARK ENTERD, TYPE CTRL + V, AND THE ENTER THE ? CHARACTER
SW2(config)#Mac-address again 7200
SW3
SW3(config)#VTP domain CCIE
SW3(config)#VTP version 2
SW3(config)#VTP mode transparent
SW3(config)#VTP password CCIErock$
TO GET THE QUESTION MARK ENTERD, TYPE CTRL + V, AND THE ENTER THE ? CHARACTER
SW4:
SW4(config)#VTP domain CCIE
SW4(config)#VTP version 2
SW4(config)#VTP mode transparent
SW4(config)#VTP password CCIErock$
TO GET THE QUESTION MARK ENTERD, TYPE CTRL + V, AND THE ENTER THE ? CHARACTER
I have started this discussion for CCIE R&S v5 H1.0 LAB Solution Verification. We will verify H1.0 Lab solution one by one so we can pass CCIE R&S LAB.
Lets start now with LAYER 2 TECHNOLOGY
1.1 SWITCH ADMINISTRATION
Configure the ACME headquarters network (AS 12345) as per the following requirements
- The VTP domain must be set to CCIE
- Use VTP version 2
- SW1 must be the VTP server and SW2 must be the VTP client
- Secure all VTP update with an MD5 digest of the ASCII string CCIErock$
- In order to avoid as much as possible unknown unicast flooding in all VLANs the administrator
before being refresh,
Configure the network of the new York office (AS 34567) as per the following requirements
- The VTP domain must be set to CCIE
- Use VTP version 2
- SW3 and SW4 must no advertise their VLAN configuration but must forward VTP advertisement
- Secure all VTP update with an MD5 digest of the ASCII string CCIErock?
I did the below configuration for Q 1.1 SWITCH ADMINISTRATION what did you think about this config
SW1:
SW1(config)#
SW1(config)#VTP domain CCIE
SW1(config)#VTP mode server
SW1(config)#VTP version 2
SW1(config)#VTP password CCIErock?
TO GET THE QUESTION MARK ENTERD, TYPE CTRL + V, AND THE ENTER THE ? CHARACTER
SW1(config)#Mac-address again 7200
SW2:
SW2(config)#VTP domain CCIE
SW2(config)#VTP mode client
SW2(config)#VTP password CCIErock?
TO GET THE QUESTION MARK ENTERD, TYPE CTRL + V, AND THE ENTER THE ? CHARACTER
SW2(config)#Mac-address again 7200
SW3
SW3(config)#VTP domain CCIE
SW3(config)#VTP version 2
SW3(config)#VTP mode transparent
SW3(config)#VTP password CCIErock$
TO GET THE QUESTION MARK ENTERD, TYPE CTRL + V, AND THE ENTER THE ? CHARACTER
SW4:
SW4(config)#VTP domain CCIE
SW4(config)#VTP version 2
SW4(config)#VTP mode transparent
SW4(config)#VTP password CCIErock$
TO GET THE QUESTION MARK ENTERD, TYPE CTRL + V, AND THE ENTER THE ? CHARACTER
This post was last modified: 01-15-2019, 05:52 PM by Pramo.